Glue/Adhesive

PRODUCT DATA SHEET

  • ITEM:
    PREMABOND 42
  • TYPE:
    High performance Polychloroprene based contact adhesive
  • DESCRIPTION:
    PREMABOND 42 is a one component adhesive based on Synthetic Rubber with special tackyfier and additives. It is specially developed for being compatible with most of the substrates. It is very good in film forming nature which gives uniform bonding to many surfaces.
  • FEATURES:
    Excellent Adhesion and High Strength
    Fire Resistant
    Excellent Boding to Porous and Non Porous Surface
    Excellent Heat Resistant
    UV Resistant
  • RECOMMENDED USE:
    Suitable for bonding of EPDM Rubber Sheets, EPDM Waterproofing Membrane, Neoprene Sheets, leather, shoe material, composite panels, wood & aluminum items, boards, leather, steel, plastic rubber sheets, carpet flooring and other items as well.


S. No. Characteristics Tested Standard Followed Typical Values
1. SPECIFIC GRAVITY (g/lt) ASTM D 1475-98 0.85±0.10
2. SOLID (%) ASTM D 1644 27±2
3. VISCOSITY SP6, RPM20 (cPs) ASTM D 2196 2500 -3500
4. FLASH POINT (°C) ASTM D 92 >100

OTHER DATA :

Characteristics Typical Values
Appearance Yellow Color Liquid
Service Temperature -25°C to 120°C
Chemical Resistance Excellent
Drying Time 10-15 Minutes
Insulation Properties Excellent
Coverage 9 to 10 m²/l (subject to application and substrate and surface)

  • SURFACE PROTECTION:
    The surface should be structurally sound, clean, dry, leveled and free from dust, curing compounds, grease and other loose debris.
  • APPLICATION PROCEDURE:
    Apply PREMABOND 42 evenly with brush, roller, spray gun or pressure feeding equipment evenly on both surfaces, wait until solvent is fully evaporated. After the evaporation of solvent in adhesive, assemble the surface by applying normal hand pressure. Special care must be taken on the edges and adhesive must be evenly applied.
  • PACKAGING:
    I Ltr. Can, 5 Ltrs. Can, 15 Ltrs Drum and 200 Ltr Drums.
  • STORAGE:
    Store product (10oC - 40oC) for maximum storage life. Higher temperatures reduces normal storage life. Lower temperatures may cause increased viscosity of a temporary nature. Rotate stock on a “first in-first out” basis.
  • CLEANING TOOLS:
    Clean immediately after use with water or white spirit if the material has dried.
  • SURFACE:
    Immediately remove any adhesive from the surface of the floor covering with a damp cloth.
  • HEALTH & SAFETY:
    Please refer to the MSDS.

MATERIAL SAFETY DATA SHEET


SECTION I - COMPANY & PRODUCT IDENTIFICATION

  • Trade Name:
    PREMABOND 42
  • Product Code:
    PB42
  • Company:
    SPECIALITY CHEMIE INTERNATIONAL
    NEW DELHI
    INDIA
    Tel - +91-9871898304
    Emergency Phone : +91 129 2238230 or +91 9899119433


SECTION II - HAZARDOUS INGREDIENTS & HAZARDS IDENTIFICATION

Unlisted ingredients are not hazardous as per the Occupational Safety and Health Administration Hazard Communication Standard.

  • Major Components:
    Hexane
    Toluene
    Heptane
    Chlorinated paraffin
    Cyclohexane

Non-Hazardous as defined by OSHA Hazard Communication Standard CFR Title 29 Part 1910.1200

Extremely Flammable
Can cause eye irritation
Can cause skin irritation
Moderate respiratory tract irritant
Harmful if swallowed
Inhalation of vapors may cause loss of feeling and weakness in the hands and feet and loss of manual dexterity. Inhalation of high concentrations may result in central nervous system effects such as dizziness, weakness, fatigue, nausea, headache, and lack of coordination.



SECTION III – FIRST AID MEASURES

  • IF In Eyes :
    Immediately flush eyes with plenty of water for at least 20 minutes retracting eyelids often.
    Tilt the head to prevent chemical from transferring to the uncontaminated eye. Get immediate medical attention and monitor the eye daily as advised by your physician.
  • IF on skin :
    Wash with soap and water. Remove contaminated clothing and launder. Get medical attention if irritation develops or persists.
  • IF Vapors Inhaled:
    Move to fresh air. Restore breathing. If necessary call a physician if symptoms persist.
  • IF Swallowed::
    Do not induce vomiting and seek medical attention immediately. Drink two glasses of water or milk to dilute. Do not give anything by mouth to an unconscious person. Induce vomiting as a last measure. Induced vomiting may lead to aspiration of the material into the lungs potentially causing chemical pneumonitis that may be total.


SECTION IV- PHYSICAL PROPERTIES

  • Physical state:
    Liquid
  • Color:
    Light Yellowish
  • Odor:
    Solvent
  • Odor Threshold:
    Not Established
  • Specific Gravity:
    0.83
  • Solids (% by weight):
    22.3
  • pH:
    Not Established
  • Boiling Pont (deg C):
    Not Established
  • Freezing/Melting Point (deg C):
    Not Established
  • Vapor Pressure (mmHg):
    Not Established
  • Vapor Density:
    Not Established
  • Evaporation rate:
    Not Established


SECTION V – FIRE/ EXPLOSION HAZARD DATA & FIRE FIGHTING MEASURES

  • Flash Point :
    -22°C, -8F
  • Auto ignition Temperature :
    Not Established
  • Lower Explosion Limit (% in air) :
    Not Established
  • Upper Explosion Limit (% in air) :
    Not Established
  • Extinguishing Media :
    Use water spray, Foam, dry chemical or carbon dioxide.

Unusual Fire & Explosion Hazards: Vapors are heavier than air and can travel to a source of ignition and flash back.

Special Fire Fighting Instructions: Persons exposed to products of combustion must wear self contained breathing apparatus and full protective equipment

Hazardous Combustion Products: Carbon dioxide, Carbon monoxide, Chlorine containing gases.



SECTION VI – REACTIVITY & STABILITY

  • Stability :
    Stable under normal Conditions.
  • Hazardous Polymerization :
    Will not occur
  • Hazardous Decomposition Products :
    Carbon dioxide, Carbon monoxide, Chlorine containing gases.


SECTION VII – TOXICOLIGICAL INFORMATION

  • Chemical Name :
    LD50/LC50
  • Hexane n OralLD50 Rat = 28710mg/kg :
    CAS# 110-54-3
  • Inhalation LC50 Rat = 48000 ppm/4H :
  • Methylcyclopentane Not Established :
    CAS# 96-37-7
  • Toluene Oral LD50 Rat = 636mg/kg :
    CAS# 108-88-3
  • Inhalation LC50 Rat =m 49000 mg/cu m/4H
  • Dermal LD50 Rabbit = 14.1ml/kg
  • Heptane :
    CAS# 142-82-5
  • Inhalation LC50 Rat = 103000 mg/cu m/4H
  • Chlorinated paraffin Oral LD50 Rat > 10ml/kg
  • Cyclohexane Oral LD50 Rat = 12705mg/kg :
    CAS# 110-82-7
  • Calcium Carbonate Oral LD50 Rat 6250mg/kg :
    CAS# 1317-65-3


SECTION VIII – WASTE DISPOSAL

This product meets the definition of Hazardous waste. It is ignitable waste class D001. Disposal via incineration is recommended.

  • Land Disposal Restrictions :
    Toulene


SECTION IX – HANDLING & STORAGE

Mildly irritating material. Avoid unnecessary exposure.
Keep away from heat, sparks and flame. Wash thoroughly after handling. Keep container closed.
Emptied container retains vapor and product residue. Observe precautions until container is cleaned.
Drums of this material should be grounded while pouring.
Do not cut or weld on or near this container.
This products contains an ingredient that may release formaldehyde at heated cure temperatures.

  • Storage :
    Store in a cool, dry, ventilated location. Keep away from heat, sparks and flame. Wash thoroughly after handling. Keep container closed.


SECTION X - INFORMATION

With appropriate commercial practices, the PREMABOND 42 is safe to handle and in storage. For further information on the material or this MSDS, please contact the Technical Director at SPECIALITY CHEMIE INTERNATIONAL, NEW DELHI, INDIA at +91 9899119433



So far, you've added (sfssdf)

SHARE YOUR REQUIREMENTS

Subscribe to our Newsletter

Fill out the information below, and click "Subscribe Now".

 

Contact

  • Khalid Al Saleh Trading Co. L.L.C.
    802 FAYA BUSINESS PARK Tower
    Buheira Corniche Al Majaz II
    P.O. Box 39380,
    Sharjah.
    United Arab Emirates

  • +971-65749909
  • contact@kastrade.com

© 2024 Khalid Al Saleh Trading Co. L.L.C. All rights reserved.

Designed by: Refresh Ideas